IfcDoorStyleOperationEnum

Natural language names
Door Style Operation Enum
Change log
ItemSPFXMLChangeDescription
IFC2x3 to IFC4
    IfcDoorStyleOperationEnumMOVEDSchema changed from IFCSHAREDBLDGELEMENTS to IFCARCHITECTUREDOMAIN.
Semantic definitions at the type
Type definition

This enumeration defines the basic ways to describe how doors operate as shown in Figure 288.

Enumerator Description Figure
SINGLE_SWING_LEFT Door with one panel that opens (swings) to the left. The hinges are on the left side as viewed in the direction of the positive y-axis.
Note  Direction of swing (whether in or out) is determined at the IfcDoor.

single swing left
SINGLE_SWING_RIGHT Door with one panel that opens (swings) to the right. The hinges are on the right side as viewed in the direction of the positive y-axis.
NOTE  Direction of swing (whether in or out) is determined at the IfcDoor.

single swing right
DOUBLE_DOOR_
SINGLE_SWING
Door with two panels, one opens (swings) to the left the other opens (swings) to the right.
NOTE  Direction of swing (whether in or out) is determined at the IfcDoor

double swing
DOUBLE_SWING_LEFT Door with one panel that swings in both directions and to the left in the main trafic direction. Also called double acting door.
NOTE  Direction of main swing (whether in or out) is determined at the IfcDoor.

double swing left
DOUBLE_SWING_RIGHT Door with one panel that swings in both directions and to the right in the main trafic direction. Also called double acting door.
NOTE  Direction of main swing (whether in or out) is determined at the IfcDoor.

double swing right
DOUBLE_DOOR_
DOUBLE_SWING
Door with two panels, one swings in both directions and to the right in the main trafic direction the other swings also in both directions and to the left in the main trafic direction.
NOTE  Direction of main swing (whether in or out) is determined at the IfcDoor.

double double swing
DOUBLE_DOOR_
SINGLE_SWING_
OPPOSITE_LEFT
Door with two panels that both open to the left, one panel swings in one direction and the other panel swings in the opposite direction.
NOTE  Direction of main swing (whether in or out) is determined at the IfcDoor.

opposite left
DOUBLE_DOOR_
SINGLE_SWING_
OPPOSITE_RIGHT
Door with two panels that both open to the right, one panel swings in one direction and the other panel swings in the opposite direction.
NOTE  Direction of main swing (whether in or out) is determined at the IfcDoor.
opposite right
SLIDING_TO_LEFT Door with one panel that is sliding to the left. sliding to left
SLIDING_TO_RIGHT Door with one panel that is sliding to the right. sliding to right
DOUBLE_DOOR_SLIDING Door with two panels, one is sliding to the left the other is sliding to the right. double sliding
FOLDING_TO_LEFT Door with one panel that is folding to the left. folding to left
FOLDING_TO_RIGHT Door with one panel that is folding to the right. folding to right
DOUBLE_DOOR_FOLDING Door with two panels, one is folding to the left the other is folding to the right. double folding
REVOLVING An entrance door consisting of four leaves set in a form of a cross and revolving around a central vertical axis (the four panels are described by a single IfcDoor panel property). revolving
ROLLINGUP Door that opens by rolling up.
NOTE  Whether it rolls up to the inside or outside is determined at the IfcDoor.
rolling
USERDEFINED User defined operation type  
NOTDEFINED A door with a not defined operation type is considered as a door with a lining, but no panels. It is thereby always open.  not defined

Figure 288 — Door style operations

HISTORY  New enumeration in IFC2x.

NOTE

  1. Figures are shown in the ground view.
  2. Figures (symbolic representation) depend on the national building code.
  3. These figures are only shown as illustrations, the actual representation in the ground view might differ.
  4. Open to the outside is declared as open into the direction of the positive y-axis, determined by the ObjectPlacement at IfcDoor
  5. The location of the panel relative to the wall thickness is defined by the ObjectPlacement at IfcDoor, and the IfcDoorLiningProperties.LiningOffset parameter.
Enumeration definition
ConstantDescription
SINGLE_SWING_LEFTDoor with one panel that opens (swings) to the left. The hinges are on the left side as viewed in the direction of the positive y-axis.
SINGLE_SWING_RIGHTDoor with one panel that swings in both directions and to the right in the main trafic direction. Also called double acting door.
DOUBLE_DOOR_SINGLE_SWINGDoor with two panels, one swings in both directions and to the right in the main trafic direction the other swings also in both directions and to the left in the main trafic direction.
DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_LEFTDoor with two panels that both open to the left, one panel swings in one direction and the other panel swings in the opposite direction.
DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_RIGHTDoor with two panels that both open to the right, one panel swings in one direction and the other panel swings in the opposite direction.
DOUBLE_SWING_LEFT
DOUBLE_SWING_RIGHT
DOUBLE_DOOR_DOUBLE_SWING
SLIDING_TO_LEFTDoor with one panel that is sliding to the left.
SLIDING_TO_RIGHTDoor with one panel that is sliding to the right.
DOUBLE_DOOR_SLIDINGDoor with two panels, one is sliding to the left the other is sliding to the right.
FOLDING_TO_LEFTDoor with one panel that is folding to the left.
FOLDING_TO_RIGHTDoor with one panel that is folding to the right.
DOUBLE_DOOR_FOLDINGDoor with two panels, one is folding to the left the other is folding to the right.
REVOLVINGAn entrance door consisting of four leaves set in a form of a cross and revolving around a central vertical axis (the four panels are described by a single IfcDoor panel property).
ROLLINGUPDoor that opens by rolling up.
USERDEFINEDUser defined operation type
NOTDEFINEDA door with a not defined operation type is considered as a door with a lining, but no panels. It is thereby always open.
Formal representations
XML Specification
 <xs:simpleType name="IfcDoorStyleOperationEnum">
  <xs:restriction base="xs:string">
   <xs:enumeration value="single_swing_left"/>
   <xs:enumeration value="single_swing_right"/>
   <xs:enumeration value="double_door_single_swing"/>
   <xs:enumeration value="double_door_single_swing_opposite_left"/>
   <xs:enumeration value="double_door_single_swing_opposite_right"/>
   <xs:enumeration value="double_swing_left"/>
   <xs:enumeration value="double_swing_right"/>
   <xs:enumeration value="double_door_double_swing"/>
   <xs:enumeration value="sliding_to_left"/>
   <xs:enumeration value="sliding_to_right"/>
   <xs:enumeration value="double_door_sliding"/>
   <xs:enumeration value="folding_to_left"/>
   <xs:enumeration value="folding_to_right"/>
   <xs:enumeration value="double_door_folding"/>
   <xs:enumeration value="revolving"/>
   <xs:enumeration value="rollingup"/>
   <xs:enumeration value="userdefined"/>
   <xs:enumeration value="notdefined"/>
  </xs:restriction>
 </xs:simpleType>
EXPRESS Specification
TYPE IfcDoorStyleOperationEnum = ENUMERATION OF (
 SINGLE_SWING_LEFT,
 SINGLE_SWING_RIGHT,
 DOUBLE_DOOR_SINGLE_SWING,
 DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_LEFT,
 DOUBLE_DOOR_SINGLE_SWING_OPPOSITE_RIGHT,
 DOUBLE_SWING_LEFT,
 DOUBLE_SWING_RIGHT,
 DOUBLE_DOOR_DOUBLE_SWING,
 SLIDING_TO_LEFT,
 SLIDING_TO_RIGHT,
 DOUBLE_DOOR_SLIDING,
 FOLDING_TO_LEFT,
 FOLDING_TO_RIGHT,
 DOUBLE_DOOR_FOLDING,
 REVOLVING,
 ROLLINGUP,
 USERDEFINED,
 NOTDEFINED);
END_TYPE;

Link to EXPRESS-G diagram EXPRESS-G diagram

References  References: IfcDoorStyle

Link to this page  Link to this page